Photochromism of photopolymerized novel copolymers having spirooxazine moiety groups

Iranian Polymer Journal - A novel class of photochromic copolymer based on spironaphthoxazine (SO) moieties was smoothly prepared through the copolymerization of methyl methacrylate (MMA), butyl...     

深海环境下浮力材料的力学性能研究

浮力材料凭借其优异的机械性能和低密度,在深海装备、航空航天及生活用品中的应用越来越广泛。将空心玻璃微珠填充环氧树脂基体中采用模压的方法制备了三种密度浮力材料,对产品全方位静水压(12.5MPa)作用后的力学性能、尺寸稳定性、吸水率等进行了测试。结果表明,浮力材料经过全方位静水压作用后,压缩性能基本没有变化,剪切强度保留率在95%以上,拉伸强度和冲击强度都有所提高,尺寸稳定性好,吸水率随着静水压作用时间的延长先快速升高后趋于稳定。     

车轮多边形磨耗统计规律及关键影响因素分析

针对列车车轮多边形磨耗问题广泛存在于轨道交通运输领域,会导致车辆/轨道系统产生高频的振动冲击,严重影响车辆和轨道系统零部件的使用寿命,危及行车安全这一问题,调查了大量车轮的多边形磨耗情况并进行统计分析,掌握了高速列车车轮多边形磨耗问题的现状和特点。以18～20阶多边形磨耗车辆为例,通过理论研究和试验分析(试验分析包括车辆系统振动特性测试和转向架模态特性测试),对车轮多边形磨耗的根本原因及诱导因素进行研究。研究发现,轮轨系统在580 Hz频率附近存在固有模态是导致车辆发生18～20阶多边形磨耗的根本原因,轮轨表面的各种不平顺能激发或者加剧轮轨系统在580 Hz频率附近的模态共振,从而诱发车轮多边形磨耗的产生。该结果可为高速列车车轮多边形磨耗问题的防止和进一步研究提供参考。     

织物表面导电线路喷射打印起始端凸起形成过程研究

为提高织物表面微滴喷射打印导电线路的成形质量,针对导电线路喷射打印过程中线路沉积形貌的起始端凸起现象,利用高速相机对线路成形过程进行采集,研究微滴间融合振荡过程中左右接触角的动态变化,微滴与线路融合以及液体向线路起始端的输送过程,提出线路起始端凸起的消除方案并进行实验。结果表明:在融合振荡过程中,微滴向起始端的振荡趋势始终大于向另一侧的振荡趋势,导致打印线路起始端的织物基板润湿区域不断扩大;微滴与线路接触后,其中一部分液体润湿织物基板拓展线路长度,一部分通过线路以恒定速度输送至起始端,在线路起始端形成凸起;利用抗坏血酸溶液润湿织物表面后,成形线路起始端凸起现象得到消除,整体线路路径均匀,沉积形貌良好。     

Cross-Layer Optimization of Dynamic Packet Assignment for Video Transmission Over IEEE 802.11e Networks

Video transmission over IEEE 802.11e wireless networks still shows poor performance for large bandwidth demand and frequently changed environments. Thus, several enhancements of IEEE 802.11e were proposed. On the other hand, big frames and simultaneous sending of adjacent frames always cause packet dropping for buffer overflow. In the past, we proposed an IEEE 802.11e enhancement named DFAA and a content aware mechanism to solve the above problems. The motivation of this paper is to find a proper way to integrate these two mechanisms. A DFAA enhancement (DFAA-E) is proposed to make up the insufficiency of content aware mechanism. Experiments results show that the combination of DFAA-E and content aware mechanism improves the video decoded quality greatly. And its performance can be further enhanced by selecting the suitable settings of certain parameters.     

Finite Element Study on the Influence of Structural Parameters on the Ballistic Performance of 3D Networked Fabrics

Networked fabrics are a type of three-dimensional multilayer fabrics having predetermined interconnections between layers by combining yarns from two adjacent sublayers into one. This paper reports the research on the influence of structural parameters on the ballistic performance of networked fabrics using finite element analysis in parallel with experiment. The widths of separate and combined sections are found to affect the energy absorption (EA) of regular networked fabrics against high-velocity impact. Separate sections of networked fabrics generally outperform combined sections. The optimal width of the separate section is around 9.5 cm for both dense and loose networked fabrics when impacted at the separate section. The optimal width of combined section decreases from 2.38 cm to 1.15 cm with the decrease of weave density in this area. For the studied structural parameters, highest EAs of dense and loose networked fabrics are around 13.3% and 17.1% higher than those of their counterpart layups of dense and loose plain-woven fabrics, respectively. These findings suggest networked fabrics could be engineered to improve the ballistic performance of flexible fabrics.     

采场动压分布特征及高效瓦斯抽放技术研究

河南地区大部分煤矿所采煤层均属于三软煤层，煤层透气性差，瓦斯治理困难。现阶段河南区域煤与瓦斯突出矿井主要采用穿层钻孔及开采保护层作为区域防突措施，而低瓦斯矿井或临突矿井（低瓦斯矿井与煤与瓦斯突出矿井相邻）存在高瓦斯区时，仅仅用风排瓦斯很难达到治理效果，近些年煤矿发生瓦斯事故多数为低瓦斯矿井，所以低瓦斯矿井和临突矿井存在高瓦斯区域的工作面回采期间瓦斯治理尤为重要。根据采场“竖三带”和“横三区”理论，利用钻孔抽放效果考察法和工作突出预测指标法研究了采场围岩动压分布特征。在此基础上，通过优化动压区抽放钻孔设计，提高了瓦斯抽放效果。瓦斯抽放量提高了1.8倍，有效降低了工作面生产期间的风排瓦斯量，提高了生产效率，保证了矿井安全生产。     

氮对镀锡钢板的强化作用

通过物理化学相分析研究了3种不同氮含量镀锡板中固溶氮、化合氮的含量,结合相关理论计算了镀锡板中氮的固溶强化和析出强化对强度的贡献。结果表明:随着总氮含量从0.0021%提高到0.0103%,钢中化合氮含量下降10.1%,但是AlN析出相中的氮的含量上升10.7%。氮在提高镀锡板强度方面发挥重要作用,钢中总氮含量提高0.0082%,其对屈服强度的贡献值提升约30 MPa。     

柔性夹具技术研究

为适应快速多变的市场需求,制造企业需要设计并应用柔性夹具。介绍了柔性夹具的发展及特点,给出了柔性夹具的设计依据,并从零件结构及工艺、组成元件确定、强度与精度保证等方面分析了柔性夹具的设计方法。